Lifting program that doesn't need a rack
Replies
-
What types of equipment do they have? No rack and you said you can't keep up with the bench either. What is available to you besides the actual weights? What machines? Would make it easier to recommend something.0
-
nakedraygun wrote: »Go diy early.
More than just squat stands
Though these stands have been posted online before, I aim to improve upon existing internet plans to combine the squat stand and the bench press. It's more like a portable power rack at this point. Whatever it is, it's only about $50 and is strong enough to support a quarter ton, or even more.
Cost: approx. $50
Project Time: 1 day (plus drying time)
Difficulty: You have to be able to cut 2x4s, drill into 2x4s, put glue on 2x4s, drive screws into 2x4s, and mix and pour cement into a bucket containing the bottom of said 2x4s. If you can handle that, then you're good to go.
Tools Needed:- Drill
- Saw (any kind that can cut a 2x4, your choice)
- Sander (either electric or get a rubber sanding block to use by hand)
- Trowel or small shovel of some kind to mix cement
- Container in which to mix said cement
- 2x4 studs (you'll need about nine)
- Box of 2 1/2 inch deck screws (I like T25 star bit)
- 5 gallon buckets (two of them)
- 120 lbs. of ready to use cement (Quikrete)
- Wood Glue
- Metal Backing Plates (more info in elaborate list below)
- Twine (or some form of pliable strong rope/thread)
- Sticky Foam or Cork or something similar, and Duct Tape (optional)
- Paint / Stain (optional)
- 2 big metal "L" brackets (optional but recommended for bench press, see video at bottom)
- 2 bolts, washers, and nuts that fit the holes in your saw horse (optional, see video)
- Scrap plywood or OSB (optional, see video)
- 5 ft. length of 1 x 6 board (optional, see video)
SOURCE
This is awesome!0 -
um, what's going on with the bench press? Is the bench you're using more like A or B?They have the heavy dumbbells and the weights to put on end of bar etc. (There is a rack, in the main gym, I just don't work out there) They have every piece of equipment necessary for me to use except rack!!!!
So, not using the rack is your choice? If the rack won't come to you, go to where the rack is?
" I like to go ladies only." We all know that if there was a "Mens Only" sexist cries would be heard nationwide.
I"m not fussed about the sexist cries, my original comment was that having a rack wasn't an option, not your opinion on what gym to go to... Apart from me liking the ladies only for many reasons, the weight area in the main gym is so full of testosterone (and smelly!!!) that its another reason not to go....
Will attempt to adjust the squats, but it is a problem for bench presses as well... I don't think I can continue the program like this!
Will a kettle bell workout do me as much/nearly as much good??
as much, no. nearly as much... maybe but probably not. Especially if you're looking for similar results to a program like stronglifts.
A
B
Curious why it matters?
Even the olympic bench will only be safe for the early parts of the program without a spotter or safety bars unless OP feels like gambling that failure will only come towards the bottom of the lift, or will be something she can semi-control on the way down.0 -
nakedraygun wrote: »Go diy early.
More than just squat stands
Though these stands have been posted online before, I aim to improve upon existing internet plans to combine the squat stand and the bench press. It's more like a portable power rack at this point. Whatever it is, it's only about $50 and is strong enough to support a quarter ton, or even more.
Cost: approx. $50
Project Time: 1 day (plus drying time)
Difficulty: You have to be able to cut 2x4s, drill into 2x4s, put glue on 2x4s, drive screws into 2x4s, and mix and pour cement into a bucket containing the bottom of said 2x4s. If you can handle that, then you're good to go.
Tools Needed:- Drill
- Saw (any kind that can cut a 2x4, your choice)
- Sander (either electric or get a rubber sanding block to use by hand)
- Trowel or small shovel of some kind to mix cement
- Container in which to mix said cement
- 2x4 studs (you'll need about nine)
- Box of 2 1/2 inch deck screws (I like T25 star bit)
- 5 gallon buckets (two of them)
- 120 lbs. of ready to use cement (Quikrete)
- Wood Glue
- Metal Backing Plates (more info in elaborate list below)
- Twine (or some form of pliable strong rope/thread)
- Sticky Foam or Cork or something similar, and Duct Tape (optional)
- Paint / Stain (optional)
- 2 big metal "L" brackets (optional but recommended for bench press, see video at bottom)
- 2 bolts, washers, and nuts that fit the holes in your saw horse (optional, see video)
- Scrap plywood or OSB (optional, see video)
- 5 ft. length of 1 x 6 board (optional, see video)
SOURCE
Wow! I know my husband could make this, thanks for posting!0 -
um, what's going on with the bench press? Is the bench you're using more like A or B?They have the heavy dumbbells and the weights to put on end of bar etc. (There is a rack, in the main gym, I just don't work out there) They have every piece of equipment necessary for me to use except rack!!!!
So, not using the rack is your choice? If the rack won't come to you, go to where the rack is?
" I like to go ladies only." We all know that if there was a "Mens Only" sexist cries would be heard nationwide.
I"m not fussed about the sexist cries, my original comment was that having a rack wasn't an option, not your opinion on what gym to go to... Apart from me liking the ladies only for many reasons, the weight area in the main gym is so full of testosterone (and smelly!!!) that its another reason not to go....
Will attempt to adjust the squats, but it is a problem for bench presses as well... I don't think I can continue the program like this!
Will a kettle bell workout do me as much/nearly as much good??
as much, no. nearly as much... maybe but probably not. Especially if you're looking for similar results to a program like stronglifts.
A
B
Curious why it matters?
Even the olympic bench will only be safe for the early parts of the program without a spotter or safety bars unless OP feels like gambling that failure will only come towards the bottom of the lift, or will be something she can semi-control on the way down.
I don't know. I think it's pretty easy to figure out when you are closing in on 1-2 reps from failure when it comes to bench press. Some sort of safeties are good but IMO a person can go for quite a while before the second type of bench (without safety bars) isn't okay.0 -
I don't have any advice, but I really would mention to the staff that a rack would be great for the women's section. Maybe they just think no one would be interested, but I'll bet if they got one you wouldn't be the only one making a move for it. It's worth a shot!0
-
I've just changed from a women's only gym because the lack of a rack. I had been doing SL 5x5 with db doing goblet squats and db shoulder squats up to 14kg db, benching with db again to 14kg, we did have a bar for deadlift but plates to small which meant lifting from floor. It is doable to keep going but above the 15 kg weight I found it really hard to get weights into position, and even with barbell cleaning it into position at 30kg was tough. Three weeks now of using rack and already up to 50kg front squat. There is no way I could do that with db.
There is a post in Eat, Train progress thread on doing a barbell prog with db.
Another option is to change the number of sets and reps you're doing. If you drop your weight and change range to 8 or 12 per set then you are still getting progressive overload. That would also increase the length of time your programme could extend.0 -
Wow, a lot happened whilst I was asleep!! Thank you for all your responses!
I have a regular bench but without the rack on top so I do the bench presses on it... If there is someone there to pass the bar to me, I can increase my weight on bench press, however getting it into position is where I struggle.
I mentioned it to a PT yesterday, how unfair it is that we don't have same equipment and she rolled her eyes at me...
Does anyone have a link for a kettle bells workout? that could be something I work on for the time being..
As for Mr Sexist - I'm sorry to hear you are having issues coming to terms with the different options out there! feel free to attend Speakers Corner in Hyde Park and air your views (google it...)0 -
0
-
nakedraygun wrote: »Go diy early.
More than just squat stands
Though these stands have been posted online before, I aim to improve upon existing internet plans to combine the squat stand and the bench press. It's more like a portable power rack at this point. Whatever it is, it's only about $50 and is strong enough to support a quarter ton, or even more.
Cost: approx. $50
Project Time: 1 day (plus drying time)
Difficulty: You have to be able to cut 2x4s, drill into 2x4s, put glue on 2x4s, drive screws into 2x4s, and mix and pour cement into a bucket containing the bottom of said 2x4s. If you can handle that, then you're good to go.
Tools Needed:- Drill
- Saw (any kind that can cut a 2x4, your choice)
- Sander (either electric or get a rubber sanding block to use by hand)
- Trowel or small shovel of some kind to mix cement
- Container in which to mix said cement
- 2x4 studs (you'll need about nine)
- Box of 2 1/2 inch deck screws (I like T25 star bit)
- 5 gallon buckets (two of them)
- 120 lbs. of ready to use cement (Quikrete)
- Wood Glue
- Metal Backing Plates (more info in elaborate list below)
- Twine (or some form of pliable strong rope/thread)
- Sticky Foam or Cork or something similar, and Duct Tape (optional)
- Paint / Stain (optional)
- 2 big metal "L" brackets (optional but recommended for bench press, see video at bottom)
- 2 bolts, washers, and nuts that fit the holes in your saw horse (optional, see video)
- Scrap plywood or OSB (optional, see video)
- 5 ft. length of 1 x 6 board (optional, see video)
SOURCE
I am so going to make this.0 -
Wow, a lot happened whilst I was asleep!! Thank you for all your responses!
I have a regular bench but without the rack on top so I do the bench presses on it... If there is someone there to pass the bar to me, I can increase my weight on bench press, however getting it into position is where I struggle.
I mentioned it to a PT yesterday, how unfair it is that we don't have same equipment and she rolled her eyes at me...
Does anyone have a link for a kettle bells workout? that could be something I work on for the time being..
As for Mr Sexist - I'm sorry to hear you are having issues coming to terms with the different options out there! feel free to attend Speakers Corner in Hyde Park and air your views (google it...)
Ok, so you absolutely cannot do something like SL. Why would a gym have barbells at all, if they cannot be used in practice?
Anyway, there are strength training routines not using barbells. What are you looking for? It could be dumbbell based or bodyweight, or a combination. Kettlebells are meant for swinging, they cannot be used to build a lifting program around them.0 -
AlisonH729 wrote: »They have the heavy dumbbells and the weights to put on end of bar etc. (There is a rack, in the main gym, I just don't work out there) They have every piece of equipment necessary for me to use except rack!!!!
Can you work in the main gym with the same membership? I know you might not want to, but to keep progressing you may have to. Or ask the owner to put a rack in the ladies gym. I don't think it's fair that its not equally equipped.
What's a "Ladies gym"?0 -
Wow, a lot happened whilst I was asleep!! Thank you for all your responses!
I have a regular bench but without the rack on top so I do the bench presses on it... If there is someone there to pass the bar to me, I can increase my weight on bench press, however getting it into position is where I struggle.
I mentioned it to a PT yesterday, how unfair it is that we don't have same equipment and she rolled her eyes at me...
Does anyone have a link for a kettle bells workout? that could be something I work on for the time being..
As for Mr Sexist - I'm sorry to hear you are having issues coming to terms with the different options out there! feel free to attend Speakers Corner in Hyde Park and air your views (google it...)
Ok, so you absolutely cannot do something like SL. Why would a gym have barbells at all, if they cannot be used in practice?
Anyway, there are strength training routines not using barbells. What are you looking for? It could be dumbbell based or bodyweight, or a combination. Kettlebells are meant for swinging, they cannot be used to build a lifting program around them.
I suppose I"m looking to build muscle whilst losing weight. (Not sure what the accurate MFP language is for this but you get what I mean) I'm not looking to be a body builder, just to be strong.... As stated above, they have most equipment apart for racks....AlisonH729 wrote: »They have the heavy dumbbells and the weights to put on end of bar etc. (There is a rack, in the main gym, I just don't work out there) They have every piece of equipment necessary for me to use except rack!!!!
Can you work in the main gym with the same membership? I know you might not want to, but to keep progressing you may have to. Or ask the owner to put a rack in the ladies gym. I don't think it's fair that its not equally equipped.
What's a "Ladies gym"?
In the gym I attend there is a (massive!!!!) main gym, and then a smaller room just for women... It's not really up for discussion why and how unfair this is to the men... I live in an area where there are lots of religious Muslims and Jews who would not want to work out together with men either due to having to be too covered up whilst working out or for general modesty reasons. Having said that, there are quite a few women there who are in the Ladies gym just because they feel more comfortable....0 -
my gym also has a large gym floor and smaller separate womens section. I know some women feel more comfortable there and thats fine...but i refuse to use it on the basis of i'm just as good as the men and strong in my own right so i'll do my workout on the main floor thanks. I understand in different countries different cultures prevail and thats fair enough.
On the main floor my gym has 4 squat racks in a row (there are others dotted around too) and i just love when i look around and see there are 3 other women in the racks...i feel like we are finally making progress away from the "weights will make me bulky" myth...0 -
my gym also has a large gym floor and smaller separate womens section. I know some women feel more comfortable there and thats fine...but i refuse to use it on the basis of i'm just as good as the men and strong in my own right so i'll do my workout on the main floor thanks. I understand in different countries different cultures prevail and thats fair enough.
On the main floor my gym has 4 squat racks in a row (there are others dotted around too) and i just love when i look around and see there are 3 other women in the racks...i feel like we are finally making progress away from the "weights will make me bulky" myth...
I don't feel less then a man because I work out in a smaller, less packed, better air conditioned room. If someone feels less of a person as a result of that, its their mind that is causing that, not the area in which you work out... I have been lifting on my own, sans rack and was squatting 30kg... Seeing as I'm 12 weeks Post Partum, I'm pretty impressed with myself, but alas I can see I can't continue..0 -
I think you should work out where you feel comfortable
But I think that if the management of the gym do not provide suitable free weight equipment, which includes a rack, in the 'Ladies Only' section of the gym that I would complain .. vociferously .. until they do
0 -
nakedraygun wrote: »Go diy early.
More than just squat stands
Though these stands have been posted online before, I aim to improve upon existing internet plans to combine the squat stand and the bench press. It's more like a portable power rack at this point. Whatever it is, it's only about $50 and is strong enough to support a quarter ton, or even more.
Cost: approx. $50
Project Time: 1 day (plus drying time)
Difficulty: You have to be able to cut 2x4s, drill into 2x4s, put glue on 2x4s, drive screws into 2x4s, and mix and pour cement into a bucket containing the bottom of said 2x4s. If you can handle that, then you're good to go.
Tools Needed:- Drill
- Saw (any kind that can cut a 2x4, your choice)
- Sander (either electric or get a rubber sanding block to use by hand)
- Trowel or small shovel of some kind to mix cement
- Container in which to mix said cement
- 2x4 studs (you'll need about nine)
- Box of 2 1/2 inch deck screws (I like T25 star bit)
- 5 gallon buckets (two of them)
- 120 lbs. of ready to use cement (Quikrete)
- Wood Glue
- Metal Backing Plates (more info in elaborate list below)
- Twine (or some form of pliable strong rope/thread)
- Sticky Foam or Cork or something similar, and Duct Tape (optional)
- Paint / Stain (optional)
- 2 big metal "L" brackets (optional but recommended for bench press, see video at bottom)
- 2 bolts, washers, and nuts that fit the holes in your saw horse (optional, see video)
- Scrap plywood or OSB (optional, see video)
- 5 ft. length of 1 x 6 board (optional, see video)
SOURCEnakedraygun wrote: »Go diy early.
More than just squat stands
Though these stands have been posted online before, I aim to improve upon existing internet plans to combine the squat stand and the bench press. It's more like a portable power rack at this point. Whatever it is, it's only about $50 and is strong enough to support a quarter ton, or even more.
Cost: approx. $50
Project Time: 1 day (plus drying time)
Difficulty: You have to be able to cut 2x4s, drill into 2x4s, put glue on 2x4s, drive screws into 2x4s, and mix and pour cement into a bucket containing the bottom of said 2x4s. If you can handle that, then you're good to go.
Tools Needed:- Drill
- Saw (any kind that can cut a 2x4, your choice)
- Sander (either electric or get a rubber sanding block to use by hand)
- Trowel or small shovel of some kind to mix cement
- Container in which to mix said cement
- 2x4 studs (you'll need about nine)
- Box of 2 1/2 inch deck screws (I like T25 star bit)
- 5 gallon buckets (two of them)
- 120 lbs. of ready to use cement (Quikrete)
- Wood Glue
- Metal Backing Plates (more info in elaborate list below)
- Twine (or some form of pliable strong rope/thread)
- Sticky Foam or Cork or something similar, and Duct Tape (optional)
- Paint / Stain (optional)
- 2 big metal "L" brackets (optional but recommended for bench press, see video at bottom)
- 2 bolts, washers, and nuts that fit the holes in your saw horse (optional, see video)
- Scrap plywood or OSB (optional, see video)
- 5 ft. length of 1 x 6 board (optional, see video)
SOURCE
This piece of equipment is a beauty, love to see imagination and craftsmanship.
0 -
Wow, a lot happened whilst I was asleep!! Thank you for all your responses!
I have a regular bench but without the rack on top so I do the bench presses on it... If there is someone there to pass the bar to me, I can increase my weight on bench press, however getting it into position is where I struggle.
I mentioned it to a PT yesterday, how unfair it is that we don't have same equipment and she rolled her eyes at me...
Does anyone have a link for a kettle bells workout? that could be something I work on for the time being..
As for Mr Sexist - I'm sorry to hear you are having issues coming to terms with the different options out there! feel free to attend Speakers Corner in Hyde Park and air your views (google it...)
Ok, so you absolutely cannot do something like SL. Why would a gym have barbells at all, if they cannot be used in practice?
Anyway, there are strength training routines not using barbells. What are you looking for? It could be dumbbell based or bodyweight, or a combination. Kettlebells are meant for swinging, they cannot be used to build a lifting program around them.
I suppose I"m looking to build muscle whilst losing weight. (Not sure what the accurate MFP language is for this but you get what I mean) I'm not looking to be a body builder, just to be strong.... As stated above, they have most equipment apart for racks....AlisonH729 wrote: »They have the heavy dumbbells and the weights to put on end of bar etc. (There is a rack, in the main gym, I just don't work out there) They have every piece of equipment necessary for me to use except rack!!!!
Can you work in the main gym with the same membership? I know you might not want to, but to keep progressing you may have to. Or ask the owner to put a rack in the ladies gym. I don't think it's fair that its not equally equipped.
What's a "Ladies gym"?
In the gym I attend there is a (massive!!!!) main gym, and then a smaller room just for women... It's not really up for discussion why and how unfair this is to the men... I live in an area where there are lots of religious Muslims and Jews who would not want to work out together with men either due to having to be too covered up whilst working out or for general modesty reasons. Having said that, there are quite a few women there who are in the Ladies gym just because they feel more comfortable....
Not everyone who wants to increase strength lifts, so you need to figure out a routine you can feel comfortable with.
What equipment do they have? What are the other women doing?
Dumbbells, machines, resistance bands? What is available to you? "Every piece of equipment", honestly I doubt it (for any gym), so be more specific.
What does the staff suggest as sample routines? If it is a large gym, they probably have someone who can at least give you a generic plan and you can adapt it as needed. They must have had something in mind when they designed the room, so you need to figure out what it is.
0 -
nakedraygun wrote: »Go diy early.
More than just squat stands
Though these stands have been posted online before, I aim to improve upon existing internet plans to combine the squat stand and the bench press. It's more like a portable power rack at this point. Whatever it is, it's only about $50 and is strong enough to support a quarter ton, or even more.
Cost: approx. $50
Project Time: 1 day (plus drying time)
Difficulty: You have to be able to cut 2x4s, drill into 2x4s, put glue on 2x4s, drive screws into 2x4s, and mix and pour cement into a bucket containing the bottom of said 2x4s. If you can handle that, then you're good to go.
Tools Needed:- Drill
- Saw (any kind that can cut a 2x4, your choice)
- Sander (either electric or get a rubber sanding block to use by hand)
- Trowel or small shovel of some kind to mix cement
- Container in which to mix said cement
- 2x4 studs (you'll need about nine)
- Box of 2 1/2 inch deck screws (I like T25 star bit)
- 5 gallon buckets (two of them)
- 120 lbs. of ready to use cement (Quikrete)
- Wood Glue
- Metal Backing Plates (more info in elaborate list below)
- Twine (or some form of pliable strong rope/thread)
- Sticky Foam or Cork or something similar, and Duct Tape (optional)
- Paint / Stain (optional)
- 2 big metal "L" brackets (optional but recommended for bench press, see video at bottom)
- 2 bolts, washers, and nuts that fit the holes in your saw horse (optional, see video)
- Scrap plywood or OSB (optional, see video)
- 5 ft. length of 1 x 6 board (optional, see video)
SOURCE
Where is the "Like" Button on this... I just bought stands last night online... bummer..0 -
I love the barbells, but I also love my kettlebells. One good program to start with is Pavel Tsatsouline's Simple and Sinister - it's basically just swings and get-ups, but it will knock you on your butt every time you move up a bell size. No, kettlebells won't get you to a 2BW deadlift or a 1.5BW squat (probably), but you can get pretty damn strong with them by normal-person standards.
Pavel's site, strongfirst.com, has some other good routines too if you spend some time reading around. And Girya Girl has a whole blog category of kettlebell workouts.0 -
omg hahahaha0 -
[quote="
I don't feel less then a man because I work out in a smaller, less packed, better air conditioned room. If someone feels less of a person as a result of that, its their mind that is causing that, not the area in which you work out... I have been lifting on my own, sans rack and was squatting 30kg... Seeing as I'm 12 weeks Post Partum, I'm pretty impressed with myself, but alas I can see I can't continue..[/quote]
Its not so much about feeling less than a man I guess what i'm trying to say that a lot of times in commercial gyms women can feel segregated and intimidated by the weights room on the main floor (and i'm not saying thats why you dont want to workout there). While the ladies gym is great stop-gap in terms of giving women somewhere to work out it (in my opinion) doesnt really solve the initial problem. So when i see lots of women on the main floor it pleases me because its a small step towards having a more accessible to everyone gym...because people shouldnt be intimidate by a few men who spend more time taking selfies in the mirrors than lifting weights (joking!!)
I d hope that you get a programme that suits you - as others have suggested you may have to consider alternatives to SL or any programme that involves compound lifts - but you should be able to work out an alternative that is more than adequate.
0 -
This is sexism on the worst level, it's great more and more women are getting into lifting and and lifting heavy and the "i just want to tone" attitude has played it course. The fact that alot of women only gyms still don't have squat racks is kinda crappy. I know lots of people are like " there's no point in womens gyms" and whatever but i get it, there are dude's that go to the gym and focus and do thier thing and couldnt care who's around but you also get the young dudes in the prime of thier teens years gaucking at every girl they see, would annoy me anyway haha.0
-
It's pretty easy to find suitable substitutes and alternatives. Bodybuilding.com has a really good exercise database.
(I've had to because I don't have access to barbells and my apartment is too small to get a rack. Plus I live on the 2nd floor so my neighbor would probably end up hating me :laugh: )
Some suggestions:
Squats - Goblet Squats, Pistol Squats, Lunges/Reverse Lunges, Split Squat, Bulgarian Split Squat
Bench Press - Floor Press
Deadlifts - DB Romanian Deadlifts, DB/Vertical Swing, Single Leg Romanian Deadlift
OHP - Shoulder Press, Standing Arnold Press
BB Bent Over Row - DB Bent Over Row, Inverted Rows
ETA: Saw that you have a bench so you could do DB Bench Press. There are palms in and palms out versions, one arm or two and if you have a bench that is adjustable, you can do inclines or declines.0 -
Wow, a lot happened whilst I was asleep!! Thank you for all your responses!
I have a regular bench but without the rack on top so I do the bench presses on it... If there is someone there to pass the bar to me, I can increase my weight on bench press, however getting it into position is where I struggle.
I mentioned it to a PT yesterday, how unfair it is that we don't have same equipment and she rolled her eyes at me...
This doesn't sound like an effective way to get a rack. How about talking to management, explain you need a rack for your program and that you prefer to work out in the Ladies Only section, and ask them to either put in a rack or come up with suggestions that work for your program.
0 -
PikaKnight wrote: »It's pretty easy to find suitable substitutes and alternatives. Bodybuilding.com has a really good exercise database.
(I've had to because I don't have access to barbells and my apartment is too small to get a rack. Plus I live on the 2nd floor so my neighbor would probably end up hating me :laugh: )
Some suggestions:
Squats - Goblet Squats, Pistol Squats, Lunges/Reverse Lunges, Split Squat, Bulgarian Split Squat
Bench Press - Floor Press
Deadlifts - DB Romanian Deadlifts, DB/Vertical Swing, Single Leg Romanian Deadlift
OHP - Shoulder Press, Standing Arnold Press
BB Bent Over Row - DB Bent Over Row, Inverted Rows
ETA: Saw that you have a bench so you could do DB Bench Press. There are palms in and palms out versions, one arm or two and if you have a bench that is adjustable, you can do inclines or declines.
Thank you that sounds like a good place to start (and fall on floor in pain
Will adjust some of those into a workout for me and see what I can do...
This is sexism on the worst level, it's great more and more women are getting into lifting and and lifting heavy and the "i just want to tone" attitude has played it course. The fact that alot of women only gyms still don't have squat racks is kinda crappy. I know lots of people are like " there's no point in womens gyms" and whatever but i get it, there are dude's that go to the gym and focus and do thier thing and couldnt care who's around but you also get the young dudes in the prime of thier teens years gaucking at every girl they see, would annoy me anyway haha.
Yes it is sexism that it is not as well equipped, but tbh I am just happy it exists... I have to walk through the main gym to get in and out of women's and trust me, I don't look particularly good at that point and u can literally feel the eyes on you as you walk... the guys are very cocky and full of themselves there, suave cars, loud voices, etc etc and it reflects in their attitude towards women...0 -
nakedraygun wrote: »Go diy early.
More than just squat stands
Though these stands have been posted online before, I aim to improve upon existing internet plans to combine the squat stand and the bench press. It's more like a portable power rack at this point. Whatever it is, it's only about $50 and is strong enough to support a quarter ton, or even more.
Cost: approx. $50
Project Time: 1 day (plus drying time)
Difficulty: You have to be able to cut 2x4s, drill into 2x4s, put glue on 2x4s, drive screws into 2x4s, and mix and pour cement into a bucket containing the bottom of said 2x4s. If you can handle that, then you're good to go.
Tools Needed:- Drill
- Saw (any kind that can cut a 2x4, your choice)
- Sander (either electric or get a rubber sanding block to use by hand)
- Trowel or small shovel of some kind to mix cement
- Container in which to mix said cement
- 2x4 studs (you'll need about nine)
- Box of 2 1/2 inch deck screws (I like T25 star bit)
- 5 gallon buckets (two of them)
- 120 lbs. of ready to use cement (Quikrete)
- Wood Glue
- Metal Backing Plates (more info in elaborate list below)
- Twine (or some form of pliable strong rope/thread)
- Sticky Foam or Cork or something similar, and Duct Tape (optional)
- Paint / Stain (optional)
- 2 big metal "L" brackets (optional but recommended for bench press, see video at bottom)
- 2 bolts, washers, and nuts that fit the holes in your saw horse (optional, see video)
- Scrap plywood or OSB (optional, see video)
- 5 ft. length of 1 x 6 board (optional, see video)
SOURCE
like^0
https://www.youtube.com/watch?v=V5eKgpZobA4
This discussion has been closed.
Categories
- All Categories
- 1.4M Health, Wellness and Goals
- 393.6K Introduce Yourself
- 43.8K Getting Started
- 260.3K Health and Weight Loss
- 175.9K Food and Nutrition
- 47.5K Recipes
- 232.5K Fitness and Exercise
- 431 Sleep, Mindfulness and Overall Wellness
- 6.5K Goal: Maintaining Weight
- 8.6K Goal: Gaining Weight and Body Building
- 153K Motivation and Support
- 8K Challenges
- 1.3K Debate Club
- 96.3K Chit-Chat
- 2.5K Fun and Games
- 3.8K MyFitnessPal Information
- 24 News and Announcements
- 1.1K Feature Suggestions and Ideas
- 2.6K MyFitnessPal Tech Support Questions